選擇一個適用的臥式混合機并使用得當，將明顯提高混合料的質量，并很快就會在生產過程中反映出良性效果。如果能進一步掌握自配混料的技術，還可使物料成本大大降低，從而提高利潤。但選擇及使用臥式混合機需注意以下幾點：
1．根據每天生產量挑選臥混機。因混合機每批物料加工時間約10分鐘，加上出料及進料的時間，每批物料加工時間可按15分鐘計，則1小時可以連續加工4批料。如選擇每批加工量100千克的混合機，則每小時可加工400千克。用戶可以根據自己的需要挑選臥式混合機。
According to a daily production volume pick lying mixing machine. Materials processing time for each batch mixer for about 10 minutes, with the materials and feeding time, each batch of materials processing time can be 15 minutes total, then 1 hour continuous batch processing 4. If you choose the amount of 100 kg per batch processing mixer, then processed 400 kg per hour. The user can choose according to their needs horizontal mixer.
2．使用臥式混合機要注意投料的次序。一般是先投大料，如玉米粉、豆粕粉等，然后 再投小組分料，如預混料。注意預混料一定不用螺旋提升機投料，應用一次性翻斗式投料，或用人工投料，這樣可以避免預混料中有效成分的離析流失。
Note that the use of horizontal mixer feeding order. Generally the first to vote aniseed, jade rice, soybean powder, and then put the group divided materials, such as premix. Note premix must not spiral elevator feeding, application disposable tipping bucket feeding, or by artificial feeding, so to avoid the loss of premix segregation of active ingredients.
3．按設計原理，螺旋帶式混合機中螺旋帶與殼體之間的間隙可以為4毫米～10毫米，物料可以用摩擦力帶動全部參加混合。但由于粉碎粒度及物料的摩擦系數不一樣，因此會使各種組分的物料參加混合的時間不一樣，造成產品的不均勻性。目前有的廠家已意識到這一點并對產品作了改進。一種是注意加工精度，使底隙減少到3毫米左右；另一種是將主軸與殼體之間做成位置可調整的形式，根據磨損量可經常調整螺旋帶與殼體之間的間隙。在選擇混合機時，這兩種形式的產品應是最佳選擇。
According to the design principle, the gap helical ribbon mixer in between the belt and the casing can be 4 mm to 10 mm, the material can be mixed with friction drive all participated. However,due to the friction coefficient of crushed material is not the same size and therefore will participate in a variety of materials component mixing time is not the same, resulting in product uniformity. Currently, some manufacturers have been aware of it and the product has been improved. A note processing accuracy, so that the end of the gap is reduced to about 3 mm; the other is formed between the shaft and the housing in the form of adjustable position, the gap between the shell and spiral belt can always adjust the amount of wear . In the choice of the mixer, the two forms of the product should be the best choice.
4．使用臥式混合機，應在混合機啟動后再逐批投料。混合結束放料時也不要停機，出凈料后再混合一批。如果滿載后再啟動，會引起動力距太大而燒毀電機。
Use horizontal mixer, batch feeding should start after the mixer. At the end of the discharge mixing and do not stop, the net material and then mixed batch. If the full load and then start, it will cause too much power from the motor and burned.
5．根據臥式螺旋帶式混合機工作原理，用于攪拌混合的雙螺旋帶向相反方向推送物料的能力應是基本一致的。由于內螺旋帶的螺距應小于外螺旋帶，為達到推送物料的能力一致，內螺旋帶的螺距應小于外螺旋帶，而寬度應大于外螺旋帶，否則會使物料向一個方向集中。因此，在選擇臥式混合機時要注意這一點。
According horizontal ribbon mixer works, the ability for mixing with the double helix in the opposite direction to push the material should be basically the same. Since the pitch spiral bands should be less than the outer spiral bands, push the material to achieve consistent ability to pitch spiral bands should be less than the outer spiral bands, and the width should be greater than the outer spiral bands, otherwise it would focus on the material in one direction. Therefore, the choice of horizontal mixer to pay attention to this point.
6．選擇臥式螺旋帶式混合機要注意出料方式。應與供應商及時溝通選擇適合自己工藝的閥門形式，同時不要選擇側口的出料形式。原因是當混合機在規定時間完成攪拌混合后，最短時間內一次放清可保證物料的均勻度；如用側口螺旋帶逐漸放凈，一是耽誤時間，達不到預期生產率，二是物料本已達到最佳均勻度，過度攪拌反而會使物料離析，破壞了均勻度，從而失去了選用臥式混合機的意義。
Select horizontal ribbon mixer should be noted that the material way. Timely communication with suppliers should choose their own form of valve technology, and do not select the material in the form of side population. The reason is that when the mixer, mixing is completed in a specified time, the shortest time to put clear to ensure uniformity of the material; such as helical ribbon with a side port gradually put the net, one delay time, less than expected productivity, and second materials this has been the best uniformity, but will make the material segregation excessive agitation, undermining the uniformity, thus losing the choice of horizontal mixer significance.